Hydrocyclone Rubber Liner Parts

Hydrocyclone Lining Parts Is The Most Important Part Of The Whole Hydrocyclone. Because The Hydrocyclone Deals With Solid-Liquid Mixture Medium, Its Wear On The Hydrocyclone Is Quite Strong. Therefore, Wear-Resistant Lining Is Needed To Protect The Normal Operation Of The Cyclone. After a Period Of Work, The Lining Needs To Be Replaced. So The Wear-Resistant Linings Produced By Our Company Can Be Better Applied To The Whole Replacement Parts Of The Cyclone.

Cyclone Lining Parts Material:

1, Wear Resistant Rubber
2, Polyurethane
3, Silicon Carbide Ceramics

Cyclone Linings Can Be Divided Into:

1, Spigot
2, Vortex Finder
3, Cone Lining
4, Cylinder Top Lid
5, Cylinder Lining Feeding

But In General, Silicon Carbide Ceramics And Polyurethane Materials Are Very Hard, So They Are Usually Bonded Directly To The Inner Surface Of Hydrocyclones. Although It Can Be Replaced, It Takes a Lot Of Time. If It's Easy To Replace. We Usually Use Wear-Resistant Rubber Linings, Which Are Easy To Replace. Take Off The Old Rubber Lining And Install The New One.

In Addition, For Some Small-Sized Cyclones, Pure Polyurethane Materials Can Be Used, Without The Need For Steel Skeleton To Provide Pressure.

In Addition, The Hydrocyclone Rubber Lining Parts Is Also Our Company's Main Products. At Present, The Maximum Is FX 838 FX 660. But The Dust Nozzles Of Hydrocyclones Are Usually Made Of Silicon Carbide Ceramics.

HydrocycloneRubber Lining Technical Requirements

1, The Shell Of Hydrocyclone Can Be Rolled Or Cast By Steel Plate.

2, The Rubber Or Polyurethane Lining Of Hydrocyclones Shall Conform To The Relevant Standards And Shall Be Manufactured In Accordance With The Approved Drawings And Technical Documents In Accordance With The Prescribed Procedures.

3, Under The Given Pressure, The Side Walls Of Hydrocyclones Are Not Allowed To Be Deformed, And There Is No Leakage At All Joints.

4, The Supply Range Of Hydrocyclones Includes The Whole Machine And Parts And Vulnerable Parts Such As Overflow Pipes, Sand Discharge Pipes, Valve Linings And So On As Stipulated In The Contract.

5, The Exposed Surface Of Hydrocyclones Should Be Coated With Antirust Primers For Two Times And Then Topcoat. Paint Should Be Uniform, No Flow Marks, Spalling And Cracks And Other Defects.

6, The Polyurethane Working Surface In The Hydrocyclone Should Be Smooth And Smooth. a Hydraulic Cyclone Below 125mm Diameter Is Not Allowed To Have a Convex Concave Larger Than 1mm On The Internal Working Surface; a Hydraulic Cyclone With a Diameter Of 125~355mm Is Not Allowed To Have An Attapulgite Larger Than a 2mm; a Hydrocyclone With a Diameter 500~1000mm Is Not Allowed To Have a Concave And Convex Larger Than 5mm.

7, The Working Surface Of The Same Sized Hydrocyclone Made Of The Same Rubber Should Be Uniform. The Working Surface Of Hydrocyclone Made Of Diabase Cast Stone, Alloy Cast Iron Or Cold Hard Cast Iron Is Not Allowed More Than 3mm, And The Working Surface Of Hydrocyclone Made Of Polymethanmethanoethyl Ester And Wear-Resistant Rubber Is Not Allowed To Have Bubbles And Defects With Depth More Than 2mm And Area Greater Than 80mm2.

Our Leading Products Are Divided Into: Mine Hydraulic Classification Cyclone Series, Coal Used Heavy Medium Separation Cyclone Series, Chemical Plant With Concentrated Cascade Cyclone Series, And So On.

Hydrocyclone Can Be Made Into Polyurethane Elastic Hydrocyclone With High Wear-Resistant Lining, Rubber Hydrocyclone With Wear-Resistant Lining, Ceramic Hydrocyclone With High Aluminum Lining, Etc.